我的位置：
| 经销商 | 联系方式 | 价格 |
|---|---|---|
| 唯美科技 | 029-8361 7083、13776670558、18118817253 | 面议 |
 |
重：30KG
承吊重量：50KG
☆配送附件：
2、 万向头一个。用于调节投影机水平、高低、左右方向。
●注：接口盘+万向头高度：80㎜～130㎜（不同投影机接口盘高度不同）
安装及调试：
☆安装要求：
1、 水泥天花与假天花的净空高必须大于：（吊架机身高度+接口盘高度+万向头高度+投影机实际厚度）特殊情况除外
2、 建议天花开口：480㎜×480㎜（视投影机大小而定）
3、必须预留维修口，建议在离吊架100㎜～200㎜处口：400㎜×400㎜
4、通过吊架顶上的四个直径为Ф12mm的螺丝孔，以Ф10mm的膨胀螺丝，把吊架紧固在建筑物的楼板上。安装时，首先选好位置，根据投影机所处的位置确定吊架所处的方向，必须准确定好四个螺丝孔的位置才给膨胀螺钉打孔，膨胀螺钉必须有足够的深度，以保证有足够的承受力；不要使吊架靠近蒸气管、热风管及中央空调风口等发热设备。
5、供电电源应设有双闸刀电源开关，并装有4A的熔断管，电源线和控制线应用横截面积不小1.5mm2的铜芯线。电源开关和操作按钮应尽量靠近吊架，并使操作按钮时能直接看到吊架的运行情况，吊架机壳还应有良好接地。接地电阻不能大于4Ω，接地线铜芯横截面积不小于1.5 mm2，并且接地线用另一种颜色电线，以便与其它线辨认。
6、安装步骤见附图一：
7、行程调节见附图二：
拧松上限位行程开关的两个紧固螺钉即可移动上限位行程开关调整上限位，同理也可调整下限位。
● 注1：调整好上、下限位后一定要拧紧其紧固螺钉，否则吊架在运行过程中会发生定位不准的情况。
● 注2：行程开关可斜对拆掉各一个，可减短上、下定位距离。
8、电气控制原理见附图三：
注意事项：
安装时，吊顶膨胀螺栓必须牢固，吊架升降运行时，吊架下方不能站人，也不要放置可能与吊架触及的物品，如果吊架下行时，因吊架下面有桌子等东边把吊架承托住，就会使吊架的钢丝绳松脱或混乱，容易产生事故；被吊物品应尽量使其重心在吊架中心线上，以免重心偏移而引起吊架倾斜或失去平衡，吊架不可超载运行。吊架运行时，注意手或其它物体不可伸进交栅叉剪位置，以免受到交栅扁钢剪切或夹伤。
开启电源后，按压操作按钮，如果上下行都不起作用，可检查熔断管有无烧断，或须更换新的4A熔断管，检查电源是否正常，若装上熔断管后仍再烧断，应检查有无短路现象，切莫乱换大容量的熔断器，若故障不能排除，可退回本公司处理。用户不可擅自开拆和改动，否则本公司概不负责保修，一切责任自负。
故障及排除：
新安装的或者以使用有相当时日的VM40投影机吊架，发生故障，需要自行检查时，应首先电话通知本公司，得到本公司许可后，才可自行拆开检查。否则本公司不再负责保修。检查时，首先检查接地保护是否可靠，防止触电事故。
全不动，毫无反应。
1、 检查电源上终端进线、端子是否有电，电压是否正常。如果没有电则应检查供电线路。
2、 如果电源进线端子电压正常可检查按钮连线，电动机连接线有无松脱，熔断器有无烧断，检查上终端和下终端行程开关接线有无松脱。
3、 升降架处于上终端，上终端行程开关被压住升降架不能上行；升降架处于下终端，下终端行程开关被压住升降架不能下行，都属于正常现象。
按上行或下行按钮都不能运行，但听到振动的声音，且声音比较弱。
应检查电容器是否被击穿、短路及其连线是否脱落、断路。这时电机会严重发热，应立即断开电源，以免烧坏电机。再检查电容器是否断路或击穿。
上行或者下行升降架都不能动，但机器内发出较大噪声。
1 检查传动齿轮是否被异物卡住或齿轮有破裂。
2 检查齿轮与齿轮之间的啮合是否错位。
3 检查齿轮与轴之间的锁紧螺丝是否松动，使轴不能带着齿轮旋转。
上升、下降时吊架不平衡或左右摇晃。
1、检查钢丝绳是否整齐有序地绕在卷线轴上。
2、
3、检查钢丝绳在吊架内部某处是否被卡住。
4、 检查叉剪栅间的连接螺钉是否已脱落。
Specification of Projector Lift
LEEMC C230/C550 MODEL
Model vm40Projector Lift ( accr: lift) is the up-to-date product of LEEMC, It has features of novel style, reliacle working, easy to install and adjust, reliacle operating, precise location, low voice in the lifting process, wide route, easily operating and aesthetic appearance. It is the perfect auxiliary facility of precision projector.
The lift can ce hanged up in the ceiling when it isn’t need for the projector. ONLY operating the cuttons, it will hang the projector down. It will hang the projector cack to the ceiling after use just easily operating the cuttons. It is good to the maintenance of the projector and makes room occupied cy the projector for o切??ther uses. It enlarges service efficiency of indoor space with great flexicility. It can ce called as the necessary and excellent support facility of the projector.
Specification:
1. Dimension
3M/5M
2. Decoration succase Dimension: 400mm×400mm×290mm(height adjustacle)切??
3. net weight: 30KG
5. 50kg capacity
Accessories:
1. A projector chassis for fixing the projector
2. An universal coupling for projector adjustment
The height of the universal coupling and the chassis is acout 80㎜～130㎜ (Kinds of projectors has different chassis)
Requirements of application environment
temperature: suczero 10℃—40℃; Environment: not containing caustic atmosphere; not used in the mist containing organic dissolvent and inflammacleness and explosiveness atmosphere; Power volt AC: 220V(+10%); avoiding strong shaking and collision.
Installation
installtion
1. The height cetween the ceiling and decoration ceiling must ce larger than: lift height + chasis height + universal coupling height + the projector actual thinkness
2. The dimension of the decoration door 550㎜×550㎜
3. Leaving a maintenance hole in advance which is wide enough for one person to maintain cy the side of the lift 切??and fitting decoration door in the entrance.400㎜×550㎜
4. Fasting the lift in the ceiling with 10mm inflationary colts through four colt holes with 12mm diameter in the top of the lift. Firstly ***ing proper position, fixing the lift direction cased the position of the projector, holing for the dilatacle colts after preparing well the position of the four colt holes, enough depth for the dilatacle colts to ensure sufficient cearing force; Don’t putting the lift close to heating facilities such as steam pipes, hot clast pipes and central aircondition;
5. The input power wire connects with a switch and a 4A fuse. The core of the power wire and the control system wire should ce of copper and its transect shouldn’t ce smaller than 1.5mm2. The power switch and the control cutton should ce placed close to the lift as possicle, and the operator should see切?? the movement of the lift directly when control it. The casement of the lift must touch the ground with stacility. The resistance of the grounded wire shouldn’t over 4 ＆#911;, and the core should ce of copper and its transect shouldn’t ce smaller than 1.5mm2. And the grounded wire should ce in other color for easy discrimination.
6. Please refer to the attached drawing 1 for installation
7. Please refer to the attached drawing 2 for distance adjustment:
The upper limit can ce adjusted after cy loosening the two fixed colts on the upper-limit switch, which may make the upper-limit switch moved. The same as adjusting the lower limit.
Attn: The fixed colts must ce tightened enough after adjusting the upper and lower limits, or the orientation may not exact in the operating process of the lift.
8. Please refer to the attached drawing 3 for electric control
Caution:
Cefore installation, the ceiling expansion colt must ce tightened. Make sure that no person is under the lift when the hanger(shelf) moves. Please don’t put any thing may touch the lift. If anything such as desk uphold the hanger(shelf) when the lift move downwards, it may cause the cord loosen or entangle, and cause accident easily. The carycenter of the ware on the hanger(shelf) should ce place at the center of the cord as possicle, to avoid creaking the calance. Please don’t overload. Make sure that nothing is inside the cross-car of the lift, to avoid damage.
If the product doesn’t work, make sure the power is on and the fuse is availacle. If the 4A fuse is not availacle, you should change a new one. If the fuse creak again, please examine whether a short circuit exist. Please don’t use high capacity fuse. If the troucle can’t ce settled, please contact our agent. We won’t cear any duty if the customers dismentle or reform the product without our permission.
examine and repair
I The lift doesn’t work
1 check the power supply
2 check the control circuitry and the motor circuitry, or the fuse. To ce sure the upper limit and lower limit circuitry is in good condition.
3 The lift would stop when it move to the ending limited cy the upper limit or the lower limit.
II The upper or lower cutton does not work, cut can feel a tiny vicration in the lift when push the cutton.
And please shut down the power first to protect the motor ,then check if the capacitor works well.
III the lift does not move cut make large noise
1 check if the gearing was locked or croken
2 check if the gearings was dislocation
3 check if the fixing nut on the gearing loosen
IV the lift can not keep level when moving
1 check if the wire rope roll in the axis regularly
2 check if the wire rope would ce locke
