| DTP T/R DP 4K 230 |
|
specification |
 |
| Frame rate 1 |
24, 25, 30 fps |
| Chroma sampling 1 |
4:4:4 or 4:2:2 |
| Color bit depth 1 |
8 bits per color |
| Signal type |
DisplayPort, HDCP |
| Max. video data rate |
10.8 Gbps (2.7 Gbps per lane) |
| NOTE |
1 Subject to the maximum data rate limit. Use our calculator ( http://www.extron.com/product/videotools.aspx ) to determine video parameters supported by this data rate. |
|
| NOTE |
This product consists of a transmitter (DTP T DP4K 230) and a receiver (DTP R DP4K 230), sold separately, with atwisted pair cable linking the transmitter and receiver. |
|
|
| Video |
| Maximum data rate |
Up to 10.8 Gbps (2.7 Gbps per lane) |
| Maximum pixel clock |
|
| Transmitter |
300 MHz |
| Receiver |
268 MHz |
| Resolution range |
Up to 2560x1600*@ 60 Hz or
4K (4096x2160) @ 30 Hz, UHD (3840x2160) @ 30 Hz
(* reduced blanking) |
| Color bit depth |
8, 10, or 12 bits — subject to the maximum data rate limit |
| Formats |
RGB and YCbCr digital video |
| Standard |
DisplayPort 1.1a, HDCP 1.4 |
| NOTE |
Only Single Stream Transport (SST) is supported. |
|
|
| Video input — transmitter |
| Number/signal type |
1 DisplayPort |
| Connector |
1 female DisplayPort |
|
| Interconnection between transmitter and receiver |
| Signal type |
DTP 230 |
| Connector |
1 female RJ-45 per unit |
| Termination standard |
TIA/EIA T568B |
| Signal transmission distance |
|
| 1080p @ 60 Hz |
Up to 230' (70 m) using shielded twisted pair (STP) cable or XTP DTP 24 STP cable |
| 2560x1600 @ 60 Hz |
Up to 130' (40 m) using shielded twisted pair (STP) cable or XTP DTP 24 STP cable |
| 4K/UHD @ 30 Hz |
Up to 130' (40 m) using shielded twisted pair (STP) cable or XTP DTP 24 STP cable |
| Cable requirements |
Solid conductor, 24 AWG or better |
| Cable recommendations |
400 MHz bandwidth, STP (shielded twisted pair) |
| NOTE |
Extron XTP DTP 24 shielded twisted pair cableis strongly recommended for optimal performance. |
|
| NOTE |
Input and output mode signaling:
DTP : HDMI with embedded audio, analog audio, RS-232 and IR, and remote power
HDBaseT : HDMI with embedded audio plus RS-232 and IR |
|
|
| Video output — receiver |
| Number/signal type |
1 DisplayPort |
| Connectors |
1 female DisplayPort |
|
| Audio |
| Gain |
Unbalanced output: 0 dB; balanced output +6 dB |
| Frequency response |
20 Hz to 20 kHz, ±0.5 dB |
| THD + Noise |
0.03% @ 20 Hz to 20 kHz at maximum output |
| S/N |
>90 dB, at maximum input (unweighted) |
| Stereo channel separation |
>80 dB |
| Digital sampling |
48 kHz |
| Bit depth |
16 bit |
|
| Audio input |
| Signal type |
|
| Analog audio (over DTP) |
Stereo (2 channel), balanced/unbalanced |
| NOTE |
Analog audio is not embedded onto the DisplayPort signal. Embedded digital audio is not de-embedded from theDisplayPort signal. |
|
| Digital audio |
Embedded digital audio on DTP signal |
| Embedded digital audio source formats |
2-ch PCM, PCM, Dolby Digital 2/0 Surround, Dolby Digital 2/0, DTS Digital Surround 5.1, DTSES Matrix 6.1, DTS-ES Discrete 6.1 |
| Connector |
(1) 3.5 mm stereo jack, 2 channel; tip (L), ring (R), sleeve (ground) |
| Impedance |
>10k ohms, DC coupled |
| Nominal level |
-10 dBV (316 mVrms) |
| Maximum level |
+7 dBV (unbalanced) |
| NOTE |
0 dBu = 0.775 Vrms, 0 dBV = 1 Vrms, 0 dBV≈ 2 dBu |
|
|
| Audio output |
| Signal type |
|
| Analog audio (over DTP) |
Stereo (2 channel), balanced/unbalanced |
| NOTE |
Analog audio is not embedded onto the DisplayPort signal. Embedded digital audio is not de-embedded from theDisplayPort signal. |
|
| Digital audio |
Embedded digital audio on DTP signal |
| Embedded digital audio source formats |
2-ch PCM, PCM, Dolby Digital 2/0 Surround, Dolby Digital 2/0, DTS Digital Surround 5.1, DTSES Matrix 6.1, DTS-ES Discrete 6.1 |
| Impedance |
50 ohms unbalanced, 100 ohms balanced |
| Gain error |
±0.2 dB channel to channel |
| Maximum level (600 ohm) |
>+14 dBu, balanced |
| Connectors |
|
| Digital audio |
Female DisplayPort |
| Analog audio |
(1) 3.5 mm captive screw connector, 5 pole |
|
| Communication — external device (pass-through, unidirectional or bidirectional) |
| Serial control port input/output |
|
| Transmitter |
RS-232 via (1) 3.5 mm, 5 pole captive screw connector for RS-232 control (±5 V) (connector is shared with IR control port) |
| Receiver |
1 set of proprietary signals on a female RJ-45 jack |
| Serial control port output/input |
|
| Transmitter |
1 set of proprietary signals on a female RJ-45 jack |
| Receiver |
RS-232 via a 3.5 mm, 3 pole captive screw connector |
| Baud rate and protocol |
300 to 115200 baud, 8 or 7 data bits, 1 or 2 stop bits, non-parity (default), even or odd parity |
| Serial control pin configuration |
1 = Tx, 2 = Rx, 3 = Gnd |
| IR control port |
(1) 3.5 mm, captive screw connector, 5 pole (connector is shared with RS-232 control port)
TTL level (0 to 5 V) modulated infrared controlfrom 30 kHz up to 60 kHz |
| IR control pin configuration |
3 = Gnd, 4 = IR Tx, 5 = IR Rx |
|
| General |
| Power supply |
External
Input: 100-240 VAC, 50-60 Hz
Output: 12 VDC, 1.5 A, 18 watts |
| Power consumption |
|
| Transmitter |
|
| Device |
3.4 watts, 12 VDC |
| Device and power supply |
4.5 watts, 100-240 VAC, 50-60 Hz |
| Receiver |
|
| Device |
5.2 watts, 12 VDC |
| Device and power supply |
6.6 watts, 100-240 VAC, 50-60 Hz |
| NOTE |
Each transmitter or receiver can be powered either locally by an external power supply or remotely by receiver or transmitter on the other end of thetwisted paircable. |
|
| Temperature/humidity |
Storage: -40 to +158 °F (-40 to +70 °C) / 10% to 90%, noncondensing
Operating: +32 to +122 °F (0 to +50 °C) / 10% to 90%, noncondensing |
| Cooling |
Convection, no vents |
| Thermal dissipation |
|
| Transmitter |
|
| Device |
11.1 BTU/hr |
| Device and power supply |
16.8 BTU/hr |
| Receiver |
|
| Device |
18.1 BTU/hr |
| Device and power supply |
25.4 BTU/hr |
| Mounting |
| Rack mount |
Yes, with optional 1U high rack shelf |
| Furniture mount |
Yes, with optional under-desk mounting kit |
| Enclosure type |
Metal |
| Enclosure dimensions |
|
| Transmitter |
1.0" H x 4.3" W x 6.0" D (quarter rack wide)
(2.5 cm H x 10.9 cm W x15.2 cm D)
(Depth excludes connectors.) |
| Receiver |
1.0" H x 4.3" W x 6.0" D (quarter rack wide)
(2.5 cm H x 10.9 cm W x 15.2 cm D)
(Depth excludes connectors.) |
| Product weight |
|
| Transmitter |
0.5 lbs (0.3 kg) |
| Receiver |
1.0 lb (0.5 kg) |
| Regulatory compliance |
CE, c-UL, UL, CE**, C-tick, FCC Class A**, ICES, VCCI |
| Product warranty |
3 years parts and labor |
| Everlast power supply warranty |
7 years parts and labor |
| NOTE |
All nominal levels are at ±10%. |
|
| NOTE |
Specifications are subject to change without notice. |
|
| (4565-031419-D13) |
