我的位置：
| 经销商 | 联系方式 | 价格 |
|---|---|---|
| 爱思创Extron电子 | 4000.398766、 021-3760 1568 | 面议 |
| IN1808 Series | |||
 specification |
|||
 |
|||
| Frame rate 1 | 24, 25, 30, 50, or 60 fps | ||
| Chroma sampling 1 | 4:4:4 and 4:2:2, 4:2:0 at input only | ||
| Color bit depth 1 | 8 or 10 bits per color | ||
| Signal type | DVI 1.0, HDMI 1.4 and 2.0, DisplayPort 1.2, HDCP 1.4 and 2.2 | ||
| Max. video data rate 1 | |||
| HDMI | 18Gbps (6 Gbps per color) | ||
| DisplayPort | 21.6 Gbps (5.4 Gbps per lane) | ||
|
|||
|
|||
| Video input | |||
|---|---|---|---|
| Number/signal type | 1 DisplayPort (HDCP compliant) 5 HDMI/DVI (HDCP compliant) 1 HDMI/DVI loop-out, configurable (HDCP compliant) 2 DTP2/XTP-configurable (HDCP compliant) |
||
| Connectors | 1 female DisplayPort 5 female HDMI type A 1 female HDMI type A loop-out 2 female RJ-45 |
||
| Horizontal frequency | 15 kHz to 135 kHz | ||
| Vertical frequency | 24 Hz to 75 Hz | ||
| Resolution range | 640x480 @ 60 Hz through 4096x2160 @ 60 Hz with 4:4:4 chroma sampling Includes 480i, 480p, 576i,576p, 720p, 1080i, 1080p, 2K, and 4K. |
||
| Standards | DVI 1.0, HDMI 2.0, DisplayPort 1.2, HDCP 1.4 and 2.2 | ||
| Video processing | |||
| Digital sampling | 8 or 10 bits per color; 600 MHz pixel clock maximum | ||
| Colors | 1.07 billion (10 bit 4:4:4 processing) | ||
| Video output | |||
| Number/signal type | 1 HDMI/DVI (HDCP compliant) 1 DTP2/XTP/HDBT, configurable (HDCP compliant) |
||
| Connectors | 1 female HDMI type A 1 female RJ-45 |
||
| Power for active cables | 1.1 W max. for the HDMI and loop out ports | ||
| Peripheral device power | 250 mA per output (HDMI and loop outputs only) | ||
| Scaled resolution | 640x4808, 800x6008, 1024x7688, 1280x7688, 1280x8008, 1280x10248, 1360x7688, 1366x7688, 1440x9008, 1400x10508,1600x9008, 1680x10508, 1600x12008, 1920x12008, 2048x12008, 2048x15368, 2560x10808,2560x14408, 2560x16008, 3840x21601,2,3,4,5,6*,7*,8*, 4096x21601,2,3,4,5,6**,7**,8**, and Custom 1-8 480p7,8, 576p6, 720p3,4,5,6,7,8, 1080i6,7,8, 1080p1,2,3,4,5,6,7,8, 2K1,2,3,4,5,6,7,8 123.98Hz,224Hz,325 Hz,429.97 Hz,530 Hz,650 Hz,759.94 Hz,860 Hz *Available on the HDMI output or to a DTP2 Rx **Available on HDMI output only |
||
| Standards | DVI 1.0, HDMI 1.4 and 2.0, HDCP 1.4 and 2.2 | ||
| Audio | |||
| Gain | Unbalanced output: -6 dB; balanced output: 0 dB | ||
| Frequency response | 20 Hz to 20 kHz, ±0.5 dB | ||
| THD + Noise | <0.1%, 20 Hz to 20 kHz at nominal level | ||
| S/N | >90 dB at maximum balanced output (unweighted) | ||
| Crosstalk | ≤-80 dB @ 1 kHz, fully loaded | ||
| Stereo channel separation | >80 dB @ 1 kHz | ||
| Supported formats | |||
| Analog de-embedding | LPCM-2Ch | ||
| HDMI pass-through | LPCM up to 7.1/24-bit/192 kHz, Dolby TrueHD, Dolby Digital Plus, Dolby Digital EX, Dolby Digital 5.1,Dolby Digital 2/0 Surround, Dolby Digital 2/0, Dolby Atmos 7.2, DTS-HD Master Audio, DTS-HD, DTS ES Discrete 6.1, DTS ES Matrix 6.1, DTS Digital Surround 5.1, DTS 2-channel | ||
| Audio input | |||
| Number/signal type | 2 stereo line level,balanced or unbalanced 2 mono mic/line level, balanced or unbalanced, (with available phantom power) 6 stereo, de-embedded from HDMI/DisplayPort (PCM only) 2 DTP2/XTP (de-embedded HDMI—PCM only, or remote unbalanced analog*) *Available only in DTP mode |
||
| Connectors | (2) 3.5 mm, 5 pole captive screw for line (2) 3.5 mm, 3 pole captive screw for mic/line 5 female HDMI type A 1 female DisplayPort 2 RJ-45 female |
||
| Impedance | >10K ohms unbalanced, >20K ohms balanced | ||
| Nominal level | Line inputs: +4 dBu (1.23 Vrms), -10 dBV (316 mVrms), adjustable Mic/line inputs: -60 dBV, +4 dBu, -10 dBV, adjustable |
||
| Maximum level | Line inputs: +21 dBu balanced, +15 dBu unbalanced Mic/line inputs: -60 dBV, +4 dBu, -10 dBV, adjustable |
||
| CMRR | >80 dB @ 1 kHz | ||
| Input gain adjustment | Line inputs: -18 dB to +24 dB in 0.1 dB steps, adjustable per input LPCM-2Ch inputs: -18 dB to +24 dB in 0.1 dB staps, adjustable per input Mic/line inputs: -18 dB to +60 dB in 0.1 dB steps, adjustable per input |
||
| DC phantom power | +48 VDC±10% (can be switched on or off per mic/line input) | ||
|
|||
| Audio output — Line out | |||
| Number/signal type | 2 stereo or 4 mono, balanced/unbalanced 1 HDMI, embedded 1 DTP2/XTP/HDPT (embedded digital, and remote balanced/unbalanced analog*) *Available only in DTP mode |
||
| Connectors | (2) 3.5 mm, 5 pole captive screw 1 female HDMI type A 1 female RJ-45 |
||
| Impedance | 50 ohms unbalanced, 100 ohms balanced | ||
| Gain error | ±0.5 dB channel to channel | ||
| Maximum level (Hi-Z) | >+21 dBu, balanced; >+15 dBu, unbalanced | ||
| Output volume range | 0 to -100 dB in 0.1 dB steps (Volume control not available on loop output) |
||
|
|||
| Audio output — power amplifier — IPCP models only | |||
| Number/signal type | |||
| IN1808 IPCP SA | 1 stereo (default) or 2 mono (2 channels total) | ||
| IN1808 IPCP MA 70 | 1 mono, 70 V line | ||
|
|||
| Connectors | |||
| IN1808 IPCP SA | (1) 5 mm, 4 pole, screw lock captive screw | ||
| IN1808 IPCP MA 70 | (1) 5 mm, 2 pole, screw lock captive screw | ||
| Load impedance | |||
| IN1808 IPCP SA | 4 ohms minimum | ||
| IN1808 IPCP MA 70 | 50 ohms minimum | ||
| Amplifier type | Class D | ||
| Output power | |||
| IN1808 IPCP SA | 25 watts per channel, 8 ohms, 1 kHz, 0.1% THD, or 50 watts per channel, 4 ohms, 1 kHz, 0.1% THD |
||
| IN1808 IPCP MA 70 | 100 watts (rms) @ 70 V, 1 kHz, 0.1% THD | ||
| Protection | Clip limiting, thermal, short circuit, DC output | ||
| Frequency response | 20 Hz to 20 kHz, -3 dB to +1 dB @ 1 W | ||
| THD + Noise | <0.1% @ 1 kHz, 3 dB below clipping | ||
| S/N | >90 dB, 20 Hz to 20 kHz, unweighted | ||
| Communications | |||
| Serial control port | 1 bidirectional RS-232, 3.5 mm, 3 pole captive screw connector (rear panel) | ||
| Baud rate and protocol | 9600, 8 data bits, 1 stop bit, no parity (default) | ||
| Serial control pin configuration | 1 = Tx, 2 = Rx, 3 = Gnd | ||
| USB control port | 1 female mini USB B (front panel) | ||
| USB standards | USB 2.0, high speed | ||
| Ethernet | |||
| Connector | 1 female RJ-45* *IPCP models use IPCP Ethernet ports. |
||
| Ethernet data rate | 10/100/1000Base-T, half/full duplex with autodetect | ||
| Ethernet protocol | ARP, ICMP (ping), IP, TCP, DHCP, HTTP, Telnet | ||
| Ethernet default settings | Link speed and duplex level = autodetected IP address = 192.168.254.254 Subnet mask = 255.255.255.0 Gateway = 0.0.0.0 DHCP = off |
||
| Storage | 512 MB user memory | ||
| Program control | Extron Product Configuration Software (PCS) program for Windows® Extron Simple Instruction Set (SIS ™ ) Microsoft® Internet Explorer® |
||
| Communications — IPCP Pro Control Processor with AV LAN — IPCP models only | |||
| Memory | |||
| SDRAM | 512 MB | ||
| Flash | 4.5 GB | ||
| Software and control options | |||
| Software | Extron Global Configurator Plus and Professional for Windows® | ||
| Control options | GlobalViewer®, eBus®, TouchLink® for Web, Touchlink for iPad®, or TouchLink Pro touchpanels | ||
| Ethernet control | |||
| Network interface controllers (NICs) | 2: 1 LAN,1 AV LAN | ||
| AV LAN network switch | 1 unmanaged 3 port switch | ||
| Connectors | |||
| LAN | 1 female RJ-45 | ||
| AV LAN | 3 female RJ-45 | ||
| Ethernet data rate | 10/100/1000Base-T, half/full duplex with autodetect | ||
| Protocols | DHCP, DNS, HTTP, HTTPS, ICMP, NTP, SFTP, SMTP, SNMP, SSH, TCP/IP, UPD/IP | ||
| Default settings | |||
| LAN | IP address = 192.168.253.250 Subnet mask = 255.255.255.0 Gateway = 0.0.0.0 DHCP = Off DNS = 127.0.0.1 |
||
| AV LAN | Link speed and duplex level = autodetect DHCP server = disabled IP address = 192.168.254.250 Subnet mask = 255.255.255.0 Gateway = 0.0.0.0 |
||
| DHCP server disabled | IP address = 192.168.254.250 DNS = 127.0.0.1 |
||
| DHCP server enabled | IP address = 192.168.254.1 Dynamic leased IP address pool = 192.168.254.100 – 192.168.254.149 Maximum lease count = 50 Lease time = 24 hours |
||
| Communications — external device (RS-232/IR over DTP2/XTP/HDBT) | |||
| Serial control pass-through ports | DTP2 Tx/XTP matrix to IN1808: RS-232 can be transmitted to and from DTP2 Tx/XTP matrix via Ethernet insertion. IN1808 to DTP2/HDBT Rx/XTP matrix: RS-232 can be transmitted to and from DTP2 Rx/HDBT Rx/XTP matrix via Ethernet insertion. |
||
| Baud rates | Up to 115200 baud | ||
| Protocol | 6 to 8 data bits 1 or 2 stop bits Even or odd parity, no parity Flow control = XON, XOFF, none |
||
| IR control pass-through port | IN1808 to TP Rx: (1) 3.5 mm, 3 pole captive screw connector TTL level (0 to 5 V) modulated infrared control from 30 kHz up to 60 kHz |
||
| IR control pin configuration | 1 = Tx, 2 = Rx,3 = Gnd | ||
| General | |||
| Power supply | Internal Input: 100-240 VAC, 50-60 Hz |
||
| Power consumption | |||
| Full power | |||
| IN1808 | 72 watts | ||
| IN1808 IPCP models | 103 watts | ||
| Power save mode | |||
| IN1808 | 34 watts | ||
| IN1808 IPCP models | 52 watts | ||
| Temperature/humidity | Storage: -40 to +158 °F (-40 to +70 °C) / 10% to 90%, noncondensing Operating: +32 to +122 °F (0 to +50 °C) / 10% to 90%, noncondensing |
||
| Cooling | |||
| IN1808 | 2 fans, air flows from right to left (when viewed from the front) | ||
| IN1808 IPCP models | 1 fan, air flows from right to left (when viewed from the front) | ||
| Fan noise | |||
| IN1808 | 42 dB(A) (ISO3746:2010 variable speed fan measured at max. speed) | ||
| IN1808 IPCP models | 37 dB(A) (ISO3746:2010 variable speed fan measured at max. speed) | ||
| Thermal dissipation | |||
| Full power | |||
| IN1808 | 201 BTU/hr | ||
| IN1808 IPCP SA | 243 BTU/hr | ||
| IN1808 IPCP MA 70 | 245 BTU/hr | ||
| Power save mode | |||
| IN1808 | 113 BTU/hr | ||
| IN1808 IPCP SA | 153 BTU/hr | ||
| IN1808 IPCP MA 70 | 152 BTU/hr | ||
| Mounting | |||
| Rack mount | Yes, with included, preinstalled brackets | ||
| Enclosure type | Metal | ||
| Enclosure dimensions | |||
| IN1808 | 1.75" H x 17.5" W x 10.5" (1U high, full rack wide) (4.4 cm H x 44.4 cm W x 26.7 cm D) |
||
| IN1808 IPCP models | 3.50" H x 17.5" W x 10.5" D (2U high, full rack wide) (8.9 cm H x 44.4 cm W x 26.7 cm D) |
||
| Product weight | |||
| IN1808 | 5.3 lbs (2.4 kg) | ||
| IN1808 IPCP models | 8.0 lbs (3.6 kg) | ||
| Regulatory compliance | CE, c-UL, UL, PSE, RoHs, and WEEE | ||
| Product warranty | 3 years parts and labor | ||
| Everlast power supply warranty | 7 years parts and labor | ||
|
|||
|
|||
| (4679-D4) | |||
