我的位置：
| 经销商 | 联系方式 | 价格 |
|---|---|---|
| 爱思创Extron电子 | 4000.398766、 021-3760 1568 | 面议 |
| DTP2 R 212 and DTP2 R 212 SA Switching Receivers | |||
 specification |
|||
|---|---|---|---|
 |
|||
| Frame rate 1 | 24, 25, 30, 50, or 60 fps | ||
| Chroma sampling 1 | 4:4:4, 4:2:2, or 4:2:0 | ||
| Color bit depth 1 | 8, 10, 12 bits per color | ||
| Signal type | HDMI 2.0b, HDCP 2.2 | ||
| Max. video data rate | 18Gbps (6 Gbps per color) | ||
|
|||
| Video | |||
| Maximum data rate | 18 Gbps (6 Gbps per color) | ||
| Maximum pixel clock | 600 MHz | ||
| Resolution range | 2560x1600 @ 60 Hz or 1080p @ 60 Hz, 12-bit color 4K (4096x2160) @ 30 Hz, UHD (3840x2160) @ 30 Hz 4K (4096x2160) @ 60 Hz*, UHD (3840x2160) @ 60 Hz *4:2:0 color space |
||
| Formats | RGB and YCbCr digital video | ||
| Standards | DVI 1.0, HDMI 2.0b, HDMI 1.4a, CEA-861F, HDCP 2.2, HDCP 1.4 | ||
| Video input | |||
| Number/signal type | 1 DTP2 1 HDMI (or single link DVI-D, with appropriate DVI-HDMI adapters) |
||
| Connectors | 1 female RJ-45 1 female HDMI, type A |
||
| Interconnection between transmitter and receiver | |||
| Connectors | 1 female RJ-45 per unit | ||
| Termination standard | TIA/EIA T568B | ||
| Signal transmission distance | Up to 330' (100m) using shielded twisted pair (STP) cable or XTP DTP 24 STP cable | ||
| Cable requirements | Solid conductor, 24 AWG or better | ||
| Cable recommendations | 400 MHz bandwidth, STP (shielded twisted pair) | ||
|
|||
| Video output | |||
| Number/signal type | 1 HDMI output | ||
| Connectors | 1 female HDMI, type A | ||
| Audio | |||
| Gain | Unbalanced output: 0 dB; balanced output: +6 dB | ||
| Frequency response | 20 Hz to 20 kHz, ±0.5 dB | ||
| THD + Noise | 0.03% @ 20 Hz to 20 kHz at maximum output | ||
| S/N | >90 dB, at maximum output (15 dBu), balanced (unweighted) | ||
| Stereo channel separation | >80 dB @ 1 kHz to 20 kHz | ||
| Bass | +12 dB to -24 dB @ 100 Hz | ||
| Treble | +12 dB to -24 dB @ 8 Hz | ||
| Audio input | |||
| Number/signal type | |||
| HDMI input | 1 embedded digital audio from HDMI | ||
| DTP/DTP2 input | 1 stereo, unbalanced analog 1 embedded digital audio from DTP |
||
| Embedded digital audio source formats | 2-ch PCM | ||
| Connectors | 1 female HDMI type A 1 female RJ-45 connector for audio over DTP |
||
| Impedance | >10k ohms unbalanced, >20k ohms balanced | ||
| Nominal level | Over DTP input: +4 dBu, -10 dBu, adjustable | ||
| Maximum level | +15 dBu at rated THD+N when input gain is set to 0dB | ||
| CMRR | >80 dB @ 1 KHz | ||
|
|||
| Audio output — Analog | |||
| Number/signal type | |||
| DTP2 R 212 | 1 stereo, balanced/unbalanced analog audio output (fixed and variable) | ||
| DTP2 R 212 SA | 1 stereo, balanced/unbalanced analog audio output (fixed and variable) 1 amplifier output (1 stereo [default] or 2 mono, 2 channels total) |
||
| Connectors | (1) 3.5 mm captive screw connector, 5-pole 1 female HDMI type A |
||
| Impedance | 50 ohms unbalanced, 100 ohms balanced | ||
| Gain error | ±0.5 dB channel to channel | ||
| Maximum level (Hi-Z) | >+21 dBu, balanced; >+15 dBu, unbalanced | ||
| Output volume range | 0 to -100 dB in 1 dB steps | ||
| Nominal level when the main volume is set to default | -2 dBu (632 mVrms) balanced output | ||
|
|||
| Audio output — power amplifier (DTP2 R 212 SA) | |||
| Number/signal type | 1 stereo or 2 mono (2 channels total) | ||
| Connector | (1) 5 mm captive screw connector, 4-pole | ||
| Load impedance | 4 ohms, minimum | ||
| Amplifier type | Class D | ||
| Output power | 8 watts rms per channel, 8 ohms, 1 kHz, 1% THD 15 watts rms per channel, 4 ohms, 1 kHz, 1% THD |
||
| Frequency response | 20 Hz to 20 kHz, +1/-3 dB @ 8 ohms | ||
| THD + Noise | <0.1% -3 dB below clipping @ 1 kHz, 8 ohm load | ||
| S/N | 90 dB, 20 Hz to 20 kHz, unweighted | ||
| Damping factor | >100 @ 8 ohms | ||
| Communications — switcher | |||
| Serial control port | 1 RS-232, 3.5 mm captive screw connector, 3-pole, rear panel | ||
| Pin configuration | Pin 1 = Tx, pin 2 = Rx, pin 3 = Gnd | ||
| Baud rate and protocol | 9600 baud, 8 data bits, 1 stop bit, no parity | ||
| USB control port | 1 female mini-USB, type B, front panel | ||
| USB standards | USB 2.0, high speed | ||
| Ethernet data rate | 10/100Base-T, half/full duplex, with autodetect | ||
| Ethernet protocol | ARP, ICMP (ping), IP, TCP, DHCP, HTTP, Telnet, SMTP | ||
| Program control | Extron PCS ® Extron Simple Instruction Set (SIS ™ ) Microsoft ® Internet Explorer ® , Telnet |
||
| Communication – RS-232/IR over DTP2 and RS-232/IR Display Control — external device (IR/RS-232 over DTP2 and sink displays) | |||
| Serial control pass-through port | 1 -232 via 3.5 mm, 5-pole captive screw connector (shared with IR port) | ||
| Baud rates | 300 to 115200 baud | ||
| Protocol | 8 or 7 data bits 1 or 2 stop bits No parity (default), even or odd parity |
||
| Serial control pin configuration | 1 = Tx, 2 = Rx, 3 = Gnd | ||
| IR control pass-through ports | 1 directional TTL level (0 to 5 V) modulated infrared control from 30 kHz up to 60 kHz | ||
| Output/DTP Rx | 3.5 mm captive screw connector, 5-pole (shared with RS-232 port) | ||
| IR control pin configuration | 3 = Gnd, 4 = IR Tx, 5 = IR Rx | ||
| General | |||
| Power supply | External Input: 100-240 VAC, 50-60 Hz Output: 12 VDC, 4A, 48 watts |
||
| Power input requirements | 12 VDC | ||
| Power consumption | |||
| Device | TBD watts, 12 VDC | ||
| Device and power supply | TBD watts, 12 VDC | ||
| Remote power capability | |||
| DTP2 R 212 | Can transmit or receive power via DTP2 | ||
| Temperature/humidity | Storage: -40 to +158 °F (-40 to +70 °C) / 10% to 90%, noncondensing Operating: +32 to +122 °F (0 to +50 °C) / 10% to 90%, noncondensing |
||
| Cooling | Convection, vents on top and sides | ||
| Thermal dissipation | |||
| Device | TBD BTU/hr | ||
| Device and power supply | TBD BTU/hr | ||
| Mounting | |||
| Rack mount | Yes, with optional rack shelf kit | ||
| Furniture mount | Yes, with optional under-desk mounting kit | ||
| Enclosure type | Metal | ||
| Enclosure dimensions | 1.00" H x 13.1" W x 6.0" D (1" high, 3/4 rack wide) (2.54 cm H x 33.3 cm W x15.2 cm D) (Depth excludes connectors) |
||
| Product weight | TBDlb (TBD kg) | ||
| Vibration | ISTA 1A in carton (International Safe Transit Association) | ||
| Regulatory compliance | |||
| Safety | CE, c-UL, UL | ||
| EMI/EMC | CE, C-Tick, FCC Class A, ICES, VCCI | ||
| Product warranty | 3 years parts and labor | ||
| Everlast power supply warranty | 7 years parts and labor | ||
|
|||
|
|||
| ( CMS-082217-D2) | |||
