| FOXBOX Tx-Rx DVI Plus |
| NOTE |
The FOXBOX Tx DVI Plus transmitter is compatible only with the following receivers:
FOXBOX Rx DVI Plus, PowerCage FOX Rx DVI Plus board, FOXBOX Rx HDMI, PowerCage FOX Rx HDMI board, FOXBOX SR HDMI, and PowerCage FOX SR HDMI board. |
|
| NOTE |
The analog audio signals are digitized in the transmitter, sent through the fiber cable, and converted back to analog audio in the receiver. |
|
| NOTE |
This transmitter and receiver are class 1 laser products. They meet the safety regulations of IEC-60825. |
|
|
| Optical fiber interconnection between transmitter and receiver |
| Number/type |
1 or 2 fiber optic |
| NOTE |
Only one fiber is required to transmit video, audio, and unidirectional data. A second fiber is required to transmit return data for bidirectional control/communication. |
|
| Connectors |
2 LC connectors |
| Operating distance |
|
| Singlemode |
30 km (18.75 miles) with singlemode (SM) cables with SM units |
| Multimode |
300 m (985') with 62.5µm OM1 multimode (MM) cableswith MM units
1 km (3280') with 50µm OM2 multimode (MM) cables with MM units
2 km (6561') with 50 µm OM3/OM4 2000 MHz bandwidth laser optimized multimode cable with a MM units |
| NOTE |
Operating distance is approximate.These are typical maximum distances that may vary depending on factors such as fiber type, fiber bandwidth, connector splicing, losses, modal or chromatic dispersion, environmental factors, and kinks. |
|
| Nominal peak wavelength |
850 nm for MM, 1310 nm for SM |
| Data rate |
4.25 Gbps |
| Transmission power |
-5 dBm, typical |
| Maximum receiver sensitivity |
|
| Singlemode |
-18 dBm, typical |
| Multimode |
-12 dBm, typical |
| Optical loss budget |
|
| Singlemode |
13 dB, maximum |
| Multimode |
7 dB, maximum |
|
| Video |
| NOTE |
*Appropriate DVI-D to HDMI cables or adapters are required for HDMI signal input/output. The FOXBOX DVI Plus Series can be used to distribute HDMI signals if you use a DVI-to-HDMI adapter. However, when using HDMI signals, these units do not transmit audio and CEC signals.
The FOXBOX DVI Plus does not support transmission of DVI signals with High-bandwidth Digital Content Protection (HDCP). |
|
| Resolution range |
Up to 1920x1200 or 1080p @ 60 Hz pixel for pixel |
| Formats |
RGB and YCbCr digital video |
| Standards |
DVI 1.0, HDMI |
|
| Video input |
| Number/signal type |
1 single link DVI-D (or HDMI*) |
| Connectors |
1 female DVI-I |
|
| Video output |
| Number/signal type |
1 single link DVI-D (or HDMI*) |
| Connectors |
1 female DVI-I |
| Nominal level |
0.8 Vp-p |
| Video delay |
1-2 frames |
|
| Audio |
| Gain |
|
| Range |
Adjustable, -18 dB to +10 dB |
| Default |
Unbalanced output: 0 dB |
| Frequency response |
20 Hz to 20 kHz, ±0.5 dB |
| THD + Noise |
0.10% @ 1 kHz at nominal level |
| S/N |
>80 dB at maximum output (unweighted) |
| Audio bits per sample |
18 bits per channel, 2 channels (L, R) |
| Sampling rate |
48 kHz |
|
| Audio input — transmitters |
| Number/signal type |
1 unbalanced stereo or 2 unbalanced mono |
| Connectors |
(1) 3.5 mm mini stereo jack |
| Impedance |
18k ohms unbalanced, DC coupled |
| Nominal level |
-10 dBV (316 mVrms) |
| Maximum level |
+8.9 dBV, (unbalanced) at 1% THD+N |
| NOTE |
0 dBu = 0.775 Vrms, 0 dBV = 1 Vrms, 0 dBV ≈ 2 dBu |
|
|
| Audio output — receivers |
| Number/signal type |
1 unbalanced stereo or 2 unbalanced mono |
| Connectors |
(1) 3.5 mm mini stereo jack |
| Impedance |
50 ohms unbalanced |
| Nominal level |
-10 dBV (316 mVrms) |
| Maximum level (Hi-Z) |
+7.6dBu, unbalanced at 1% THD+N |
| Maximum level (600 ohm) |
>+6.3 dBu, unbalanced at 1% THD+N |
| Audio delay |
1.5 frames |
|
| Control/remote |
| Serial control ports on each unit (transmitter and receiver) |
| Control |
1 RS-232, 2.5 mm mini stereo jack (front panel) |
| Pass-through |
1 RS-232, 3.5 mm captive screw connector, 5-pole (3 pins are used) (rear panel) |
| Baud rate and protocol |
|
| Control |
9600 baud, 8 data bits, 1 stop bit, no parity |
| Pass-through |
9600 to 115,200 baud |
| Serial control pin configuration |
Mini stereo jack: tip = Tx, ring = Rx, sleeve = GND |
| Program control |
Extron control/configuration program for Windows ®
Extron Simple Instruction Set (SIS ™ ) |
|
| General |
| Power supply |
External
Input: 100-240 VAC, 50-60 Hz
Output: 12 VDC, 1.5 A, 18 watts |
| Power input requirements |
12 VDC,0.6 A |
| Temperature/humidity |
Storage: -40 to +158 °F (-40 to +70 °C) / 10% to 90%, noncondensing
Operating: +32 to +122 °F (0 to +50 °C) / 10% to 90%, noncondensing |
| Cooling |
Convection, vents on top and side panels |
| Thermal dissipation |
|
| Transmitter |
4.0 BTU/hr |
| Receiver |
3.9 BTU/hr |
| Mounting |
|
| Rack mount |
Yes, with optional rack shelf |
| Furniture mount |
Yes, with optional under desk mounting kit |
| Enclosure type |
Metal |
| Enclosure dimensions |
1.0" H x 4.3" W x 6.0" D (quarter rack wide)
(2.5cm H x10.9 cm W x 15.2 cm D)
(Depth excludes connectors.) |
| Product weight |
0.7 lbs (0.3 kg) per unit, 1.4 lbs (0.6 kg) per pair |
| Regulatory compliance |
CE, c-UL UL, CE, C-tick, FCC Class A, ICES, VCCI,
Complies with the appropriate requirements of RoHS, WEEE |
| Product warranty |
3 years parts and labor |
| Everlast power supply warranty |
7 years parts and labor |
| NOTE |
All nominal levels are at ±10%. |
|
| NOTE |
Specifications are subject to change without notice. |
|
| (4399-101518-D10) |
