我的位置：
| 经销商 | 联系方式 | 价格 |
|---|---|---|
| 爱思创Extron电子 | 4000.398766、 021-3760 1568 | 面议 |
| TLC Pro 1026M Series | |||
| Display | |||
|---|---|---|---|
| Screen type | TFT Active matrix Color LCD | ||
| Size | 10.1" (25.7 cm), measured diagonally | ||
| Resolution | 1280x800 (WXGA) | ||
| Pixel density | 149 PPI | ||
| Aspect ratio | 16:10 | ||
| Color depth | 24 bit, 16.7 million colors | ||
| Transparency | 8 bit | ||
| Brightness | 420 nits (cd/m 2 ) | ||
| Contrast | 800:1 | ||
| Backlight | LED | ||
| Viewing angle | ±85° horizontal, ±85° vertical | ||
| Touch screen | Capacitive | ||
| Memory | |||
| RAM | 2 GB | ||
| Storage | 8 GB | ||
| Ethernet | |||
| Connectors | 1 female RJ-45 connector | ||
| Data rate | 10/100/1000Base-T, half/full duplex with autodetect | ||
| Protocols | DHCP, DNS, HTTP, HTTPS, ICMP, SFTP, SSH, TCP/IP, UDP/IP | ||
| Default settings | Link speed and duplex level: autodetected IP address = 192.168.254.251 Subnet mask = 255.255.255.0 Default gateway = 0.0.0.0 DHCP = off DNS = 127.0.0.1 |
||
| Software | |||
| Configuration software | Global Configurator Plus and Professional, GUI Designer | ||
| Control apps | Extron Control, iGVE | ||
| Resource management software | GlobalViewer Enterprise, iGVE | ||
| Utilities | Toolbelt, Embedded web page | ||
| Sensors | |||
| Motion sensor | On/off | ||
| Light sensor | Auto/manual | ||
| USB | |||
| Quantity/type | 1 high-speed USB 2.0 device | ||
| Connectors | 1 micro-B receptacle | ||
| Standards | USB 2.0, USB 1.1, USB 1.0 compatible | ||
| Max. data rates | Low speed (1.5 Mbps), full speed (12 Mbps), high speed (480 Mbps) | ||
| Digital input | |||
| Quantity/type | 1 digital input (configurable) on touchpanel | ||
| Connectors | (1) 3.5 mm direct insertion captive screw connector, 2 pole | ||
| Digital inputs | |||
| Input voltage range | 0 to 24 VDC, clamped at +30 VDC | ||
| Input impedance | ≥10k ohms | ||
| Programmable pullup | 1k ohms to +5 VDC | ||
| Threshold low to high | 2.8 VDC | ||
| Threshold high to low | 2.0 VDC | ||
| Contact closure | |||
| Quantity/type | 1 contact closure input on USB adapter | ||
| Connector | (1) 3.5 mm direct insertion captive screw connector, 3-pole, shared with IR port | ||
| Pin configuration | Internal pullup resistor is enabled to +5 VDC, non-selectable. The port is active when the contact pin latches to ground. |
||
| Serial | |||
| Quantity/type | 2 bidirectional RS-232 | ||
| Connector | (1) 3.5 mm direct insertion captive screw connector, 5 pole | ||
| Baud rate and protocol | 300 to 115200 baud (9600 baud = default); 8 (default) or 7 data bits; 1 (default) or 2 stop bits; no parity (default), even, or odd parity |
||
|
|||
| Relay | |||
| Quantity/type | 2 normally open relays | ||
| Relay control connectors | (1) 3.5 mm direct insertion captive screw connector,3 pole | ||
| Relay control contact rating | 24 VDC, 1 A | ||
| IR | |||
| Quantity/type | TTL level (0 to 5 V) infrared (carrier or non-carrier) up to 300 kHz | ||
| Connector | (1) 3.5 mm direct insertion captive screw connector, 3 pole, shared with Digital input | ||
| IR output carrier frequency | 30 kHz to 300 kHz | ||
| Audio output | |||
| Speaker output | 2 mono, 89 dB Max. SPL @ 0.1 m | ||
| Frequency response | 750 Hz to 20 kHz, ±5 dB | ||
| Playback format(s) | |||
| Container format | WAV (Microsoft RIFF) | ||
| Encoding | LPCM (uncompressed) | ||
| Bit depth | Unsigned 8-bit Signed 16-bit Signed 24-bit Signed 32-bit |
||
| Sampling rate | Up to 192 kHz | ||
| Audio channels | Mono or stereo | ||
| General | |||
| Power supply | Not included | ||
| Power input requirements | Power over Ethernet (PoE 802.3af, class 3) | ||
| Power consumption — Power injector (XTP PI 100) | |||
| Device | 12.9 watts | ||
| Device and power injector | 14.7 watts | ||
| Auxiliary power output | |||
| USB | 5 VDC, 275 mA | ||
| Temperature/humidity | Storage: -4 to +140 °F (-20 to +60 °C) / 10% to 90%, noncondensing Operating: +32 to +104 °F (0 to +40 °C) / 10% to 90%, noncondensing |
||
| Cooling | Convection, vents on back | ||
| Thermal dissipation — Power injector (XTP PI 100) | |||
| Device | 39.3 BTU/hr | ||
| Device and power injector | 45.3 BTU/hr | ||
| Mounting | Wall, furniture, glass, or rack | ||
| Enclosure type | Plastic | ||
 |
|||
| Enclosure dimensions | 6.84" H x 10.13" W x 1.26" D (174 mm H x 257 mm W x32 mm D) Touchpanel projects 0.65" (17 mm) from the mounting surface Total depth is 2.05" (52 mm) (front of touchpanel to back of adapter) |
||
| Adapter dimensions | 0.47" H x 1.81" W x 0.91" D (12 mm H x 46 mm W x 23 mm D) The touchpanel and adapter project 1.4" (35 mm) behind the mounting surface. |
||
| Enclosure + Adapter dimensions | 6.84" H x 10.13" W x 2.05" D (174 mm H x 257 mm W x52 mm D) |
||
| Product weight | 2.10 lbs (0.95 kg) | ||
|
|||
| Regulatory compliance | BIS, CE, c-UL, UL, C-Tick, FCC Class A, ICES, KCC, VCCI, RoHS, and WEEE. | ||
| Product warranty | 3 years parts and labor; touchpanel display and overlay components are covered for 1 year | ||
|
|||
|
|||
| (4669-D3) | |||
